Search found 44 matches

by johnnemo
Tue Aug 13, 2013 9:15 pm
Forum: Builder's Power Boats
Topic: johnnemo GF16
Replies: 42
Views: 9808

Re: johnnemo GF16

Holy Cow! 8O Its been over a year since my last post! :oops: Time to get this thing moving forward again. I ordered my hatches a few days ago but that haven't arrived yet. Can't wait to see what "Dophin Gray" looks like. The online store didn't have the two sizes I needed in any other matc...
by johnnemo
Mon Jun 11, 2012 12:26 pm
Forum: Power Boats
Topic: GF 16 - Installing Tackle Center in Rear Seat Frame
Replies: 2
Views: 748

GF 16 - Installing Tackle Center in Rear Seat Frame

Can I install a Tackle Center like this:

http://www.basspro.com/T-H-Marine-Desig ... LL_PRODUCT

in the rear seat frame (the vertical section, not the top of the seat), or will it weaken the structure?
by johnnemo
Sun Jun 10, 2012 5:10 pm
Forum: Builder's Power Boats
Topic: johnnemo GF16
Replies: 42
Views: 9808

Re: johnnemo GF16

I relocated my build outside for the messy stages. Per Joel's (shine) recommendation, I am using scrap pieces of ply to make my cleats. I used the table saw to cut 1.5" stips (I guess that's wide enough?) which will be double stacked. I will not have enough to make the rub rails, spray rails, o...
by johnnemo
Thu Jun 07, 2012 10:53 pm
Forum: Builder's Power Boats
Topic: johnnemo GF16
Replies: 42
Views: 9808

Re: johnnemo GF16

As I am thinking about the next build steps, I reviewed some of the builds I mentioned earlier in my posts. I missed a few GF 16 ones... Ziess' Build in Oregon http://forums.bateau2.com/viewtopic.php?f=12&t=18843 Also '30mill' has (3) nice pictures of his launch here: http://forums.bateau2.com/v...
by johnnemo
Tue Jun 05, 2012 8:38 pm
Forum: Builder's Power Boats
Topic: nawlin's od 18
Replies: 95
Views: 17354

Re: nawlin's od 18

Looking good. How long have you been building?
by johnnemo
Tue Jun 05, 2012 8:35 pm
Forum: Builder's Power Boats
Topic: Birmingham RB14
Replies: 84
Views: 15859

Re: Birmingham RB14

Congratulations on getting started. Posting updates on the forum motivates me to keep going - I can look back and see what I have accomplished and when I find myself on page 4 I know its time to get busy building. Good luck with the build.
by johnnemo
Tue Jun 05, 2012 6:56 am
Forum: Builder's Power Boats
Topic: johnnemo GF16
Replies: 42
Views: 9808

Re: johnnemo GF16

In 'myvoodoo's build he makes the following statement.... "I'm 69 and learned some time back that cutting corners only comes back to bite you in the butt, no matter what you are doing in life.......Yes, I might spend a extra few bucks but the finished product but it will be around a long time w...
by johnnemo
Mon May 28, 2012 10:28 pm
Forum: Power Boats
Topic: Attaching sides to Mid Seat Frames - GF 16
Replies: 1
Views: 444

Attaching sides to Mid Seat Frames - GF 16

I tried attaching the sides today and when I follow the plans and attach the sides on a level surface I found that the mid-seat frame I am attaching the sides to is 1/8" to 1/4" lower than the side panel. I guess this is because the side panel is angled and does not rest completely flush w...
by johnnemo
Mon May 28, 2012 6:58 am
Forum: Power Boats
Topic: Drain Holes for GF 16
Replies: 4
Views: 728

Re: Drain Holes for GF 16

How big do they need to be to pass a fuel line through?
by johnnemo
Sun May 27, 2012 8:44 pm
Forum: Power Boats
Topic: Drain Holes for GF 16
Replies: 4
Views: 728

Drain Holes for GF 16

What size drain holes are recommended for a GF16 for water to pass through the bottom of the bulkheads? Should I use 1/2 circles cut with a hole saw, or use a large hole bit and have the bottom of the circle be flush with the floor of the boat? Any pictures would be very helpful. Is it best to cut t...