Search found 16 matches

by Grandbassslayer
Thu Sep 23, 2021 1:33 pm
Forum: Small Boats
Topic: GV10 build and introduction
Replies: 36
Views: 3186

Re: GV10 build and introduction

The gentlemen I was watching is definitely an expert. tips from a shipwright is his channel. I am good without thinning, just thought it was an interesting observation and wanted to hear from the experienced folks on this site.
Thanks
Scott
by Grandbassslayer
Mon Sep 20, 2021 9:24 am
Forum: Small Boats
Topic: GV10 build and introduction
Replies: 36
Views: 3186

Re: GV10 build and introduction

I was just tossing out ideas for when you do large areas. It would still be a 2:1 mix, then add the alcohol, he said it evaporates out after it’s later out. I dunno the channel is called “tips from a shipwrights” and he looks like an old school do it the right way kinda guy. Just curious if that was...
by Grandbassslayer
Sat Sep 18, 2021 3:41 pm
Forum: Small Boats
Topic: GV10 build and introduction
Replies: 36
Views: 3186

Re: GV10 build and introduction

I took a belt sander to all the seams after I had all the zip ties pulled out, helped clean up all the seams and put nice rounded corners on them. I got all the exterior joints glasses with the 6” tape, good thing I got the slow hardener, still had one section that got away from me a little bit but ...
by Grandbassslayer
Mon Sep 13, 2021 10:12 pm
Forum: Small Boats
Topic: GV10 build and introduction
Replies: 36
Views: 3186

Re: GV10 build and introduction

I practiced on some scrap and have my router set nice, should work well.
Thanks guys.
by Grandbassslayer
Sat Sep 11, 2021 9:21 pm
Forum: Small Boats
Topic: GV10 build and introduction
Replies: 36
Views: 3186

Re: GV10 build and introduction

Got the 1st 6” wide tape down on all 4 sides, layer plastic wrap on them and weights. Will flip tomorrow, do the other side and get the boat back together. Any opinions on routing or sanding all the exterior edges? I don’t want sharp exterior corners, especially where the free board ties into the tr...
by Grandbassslayer
Wed Sep 08, 2021 7:32 am
Forum: Small Boats
Topic: GV10 build and introduction
Replies: 36
Views: 3186

Re: GV10 build and introduction

Correct I just used straight 2 to 1 epoxy, I feel like a dope now…lol. Guys I appreciate the help. So epoxy is just for use with glass, joining materials will always be a thickened epoxy such as gel magic. I will break it down, file, use gel magic, then lay 2 overlapping pieces of tape over the joint.
by Grandbassslayer
Tue Sep 07, 2021 11:14 pm
Forum: Small Boats
Topic: GV10 build and introduction
Replies: 36
Views: 3186

Re: GV10 build and introduction

I didn’t use gel magic, just epoxy resin, were they supposed to be gel magic?
by Grandbassslayer
Tue Sep 07, 2021 7:22 pm
Forum: Small Boats
Topic: GV10 build and introduction
Replies: 36
Views: 3186

Re: GV10 build and introduction

Thank you Evan. I came out tonight to take a look, figured I would let the boat sit on the jig a few days to relax before I tried to get that last little bit of straightening up out of it. Well the outside edge of both of the bottom puzzles pieces is coming apart. Not sure what went wrong, using the...
by Grandbassslayer
Mon Sep 06, 2021 9:42 pm
Forum: Power Boats
Topic: PH22 Strong Back
Replies: 5
Views: 593

Re: PH22 Strong Back

Any updates on this build?
by Grandbassslayer
Mon Sep 06, 2021 3:57 pm
Forum: Small Boats
Topic: GV10 build and introduction
Replies: 36
Views: 3186

Re: GV10 build and introduction

[imgur2] https://imgur.com/u97Ogho[/imgur2]

Thoughts and advice? I need to clean up the edges, add nails for proper spacing, duct tape the back sides, then use gel magic on all the joints, correct?