Search found 1146 matches

by Browndog
Wed Sep 28, 2016 9:20 am
Forum: Power Boats
Topic: Eric's C21
Replies: 3239
Views: 181704

Re: Eric's C21

Looking good!
by Browndog
Thu Sep 22, 2016 7:47 am
Forum: Power Boats
Topic: C19 build.....
Replies: 52
Views: 5754

Re: C19 build.....

The top of the transom takes a beating. In my opinion overlapping the glass over the top would be prudent.
by Browndog
Fri Sep 16, 2016 4:02 pm
Forum: Power Boats
Topic: Eric's C21
Replies: 3239
Views: 181704

Re: Eric's C21

Eric, Have had similar problems with the tape in the past. Especially the thicker finished edge. It is helpful sometimes to trim the finished edge off of the tape prior to applying as this often allows the tape to lay down better. Also, occasionally making a slit in the tape will help it to go aroun...
by Browndog
Sun Aug 21, 2016 8:31 am
Forum: Resins, Fiberglass and Paint
Topic: Sanding ply before epoxy?
Replies: 10
Views: 894

Re: Sanding ply before epoxy?

This question is a funny one because it depends on the personal experience, the size of the boat project and amount of obsessive compulsiveness of the boat builder to truly appreciate the question and provide an answer. Sanding the bare plywood before applying epoxy will theoretically improve the fi...
by Browndog
Sat Aug 20, 2016 7:39 am
Forum: Power Boats
Topic: Extreme Flats 20 build questions
Replies: 8
Views: 780

Re: Extreme Flats 20 build questions

Take a look at the GP21. It is essentially the boat you describe after modifying the xf20 with one exception. You get a small amount of V which will help you deal with the Bay chop. Having grown up around the bay myself, crabbing and fishing I can appreciate what you are looking for. The GP21 is a v...
by Browndog
Wed Aug 10, 2016 11:53 pm
Forum: Power Boats
Topic: Boat suggestion; between FS14LS and FS17
Replies: 18
Views: 1393

Re: Boat suggestion; between FS14LS & FS17

Seems like you should take a look at the flats stalker 18 (FS18). It might be closer to what you have in mind.
by Browndog
Sun Jul 24, 2016 2:08 pm
Forum: Power Boats
Topic: More C19 prop questions
Replies: 32
Views: 3639

Re: C19 - changing the prop

Even with the aluminum prop you were well below maximum RPMs. My bigger concern is how high you have to rev the motor to go at 6-7 knots which is in the displacement speed range. Something is not right. It is running just well enough to mask something else. Since you don't have motor alarms going of...
by Browndog
Sat Jul 23, 2016 8:30 pm
Forum: Power Boats
Topic: More C19 prop questions
Replies: 32
Views: 3639

Re: C19 - changing the prop

The RPMs are so much lower than maximum at the high end and so much higher at the low end, I suspect that it is not a propeller problem but probably something else like a clogged injector not giving enough fuel to one of the cylinders or another problem causing fuel starvation. 6-7 knots should come...
by Browndog
Tue Jul 19, 2016 6:45 am
Forum: Power Boats
Topic: FS17 Transom and Water line?
Replies: 16
Views: 1562

Re: FS17 Transom and Water line?

Good suggestion Larry!
by Browndog
Tue Jul 19, 2016 6:44 am
Forum: Power Boats
Topic: Eric's C21
Replies: 3239
Views: 181704

Re: Eric's C21

More blood please. :D