Thank Richard!
You guys have also had a pretty stormy fall so far. The temp here is all over the place. 55 this morning and the weekend highs will be low 80s but sunny! Bayou clean up Saturday and a big tour Sunday! Will be a busy weekend outside!
Search found 3501 matches
- Fri Oct 26, 2018 7:27 pm
- Forum: Builder's Power Boats
- Topic: FS14- Bayou City Boat
- Replies: 1402
- Views: 150287
- Fri Oct 26, 2018 1:03 pm
- Forum: Builder's Power Boats
- Topic: FS14- Bayou City Boat
- Replies: 1402
- Views: 150287
Re: FS14- Bayou City Boat
Thanks Jeff and GB. I am bespoken the heck out of this build but that is why we build instead of buy so it is our own. :lol: Piperdown my boat will have two bilge pumps. The primary will be under the sole for most the water that gets into the boat will be collected there and then a 900 gph pump that...
- Fri Oct 26, 2018 10:00 am
- Forum: Power Boats
- Topic: My cx 25
- Replies: 371
- Views: 47140
Re: My cx 25
It is a nice clean and big boat.
I remember some pictures of a couple of kids helping you. Now that it is flipped and the frames are going in do you take a head count every time you finish for the day?
I remember some pictures of a couple of kids helping you. Now that it is flipped and the frames are going in do you take a head count every time you finish for the day?
- Fri Oct 26, 2018 5:46 am
- Forum: Builder's Sail Boats
- Topic: AD16 (Tipsy) Myrtle Beach
- Replies: 2046
- Views: 227371
Re: AD16 Myrtle Beach
Oh, and a lot of electrical stuff comes telling you what it's power requirements are as for as protection. Like you need to use XX size fuse to protect it. Write all those numbers down will help you figure how much battery capacity you will need. Draw out a map of how you want your electric to run. ...
- Fri Oct 26, 2018 5:30 am
- Forum: Builders' Tips, Tools, and Tricks of the trade
- Topic: Epoxy Fillet Tool
- Replies: 26
- Views: 30995
Re: Epoxy Fillet Tool
We all have tools that we have found work best for the way we like to do some things but I am still on a quest to find that tool when it comes to "finish" fillets. One thing that Eric's tool will help is the angle you hold it is not that important so corners, double 90 degrees, will be cle...
- Thu Oct 25, 2018 9:56 pm
- Forum: Builder's Power Boats
- Topic: FS14- Bayou City Boat
- Replies: 1402
- Views: 150287
Re: FS14- Bayou City Boat
So the temperatures are starting to climb a little, I think it reached mid 70s, but I finished doing some prep work and finally painted the anchor locker. I thought the square drive screw would make it easier to install the covers on the junction boxes but they are still a little difficult to tighte...
- Thu Oct 25, 2018 9:18 pm
- Forum: Builder's Power Boats
- Topic: FS 17 - Raised Sheer
- Replies: 432
- Views: 55612
Re: FS 17 - Raised Sheer
Looks good and fitting everything before building is always a good idea.
I did not have a lot of fun filleting on the inside either.
I did not have a lot of fun filleting on the inside either.
- Thu Oct 25, 2018 9:15 pm
- Forum: Small Boats
- Topic: Franks SK14 from Japan
- Replies: 170
- Views: 43973
Re: Franks SK14 from Japan
Really nice looking box Frank. Should do nicely for a fish finder and even some nav lights if you decide.
For my kayak fishing days I used 2 12V deer feeder batteries in a soft sided camera case. It would power the gps/FF and the 360° light for a few days and still have more than 60% most the time.
For my kayak fishing days I used 2 12V deer feeder batteries in a soft sided camera case. It would power the gps/FF and the 360° light for a few days and still have more than 60% most the time.
- Thu Oct 25, 2018 4:11 pm
- Forum: Builder's Sail Boats
- Topic: AD16 (Tipsy) Myrtle Beach
- Replies: 2046
- Views: 227371
Re: AD16 Myrtle Beach
Here are some articles on the matter. You don't have to buy their stuff but their articles are pretty good info.
https://www.bluesea.com/support/articles
https://www.bluesea.com/support/articles
- Thu Oct 25, 2018 3:03 pm
- Forum: Builders' Tips, Tools, and Tricks of the trade
- Topic: Epoxy Fillet Tool
- Replies: 26
- Views: 30995
Re: Epoxy Fillet Tool
That is really a good idea. Any idea on the $$?