Search found 2084 matches
- Sat Dec 08, 2018 4:35 pm
- Forum: Resins, Fiberglass and Paint
- Topic: Kiwi Grip Grey
- Replies: 12
- Views: 1684
Kiwi Grip Grey
Hi guys, I'm going to redo my pontoon boat floor. Not the wood all ready did that a few years back. I put white kiwi grip on it. Now I want to change it to grey? I was just going to clean the white real good and put the grey over it. Do any of you see a reason why this would not work? Also I couldn'...
- Sat Nov 17, 2018 8:37 am
- Forum: Builder's Power Boats
- Topic: FS-18 - "Bare Bones"
- Replies: 1190
- Views: 109958
Re: FS-18 - "Bare Bones"
If I was looking for a strong back like this one and was going to have to build one, I'd drive 200 miles easy to pick up one AA had made. You could not come close to building one for the cost of fuel. Material would cost more plus labor, not to mention AA quality :D AA, boat looks great, you did a f...
- Mon Sep 10, 2018 10:55 am
- Forum: Power Boats
- Topic: Narfi's FS17 - Build Thread
- Replies: 1352
- Views: 185447
Re: Narfi's FS17 - Build Thread
dont know anything about that year, but I bought a new 2010 60hp Etec and I love it. Only problem I ever had with it was a coil went bad right after I bought it. Didn't strand me, just wouldn't idle right. Replaced under warranty and not a hic up since. But I believe the 2010 is a different motor th...
- Wed Feb 28, 2018 8:26 am
- Forum: Builder's Power Boats
- Topic: OD18 - NH
- Replies: 506
- Views: 72738
Re: OD18 - NH
Hi Larry, I knew I had seen it done that way but couldn't remember who's build I had seen it in. I am considering the same sort of thing if I run out of room for the fill and vent pipes as I'm trying to keep the casting deck a little lower than the plans so that I can get some cushions made for it....
- Tue Feb 27, 2018 11:09 pm
- Forum: Builder's Power Boats
- Topic: OD18 - NH
- Replies: 506
- Views: 72738
Re: OD18 - NH
I went with a 25 gallon, but I recessed it into the sole to keep it lower. I put a drain in that goes to the bilge.
- Sat Feb 17, 2018 8:22 am
- Forum: Builder's Power Boats
- Topic: OD18 - NH
- Replies: 506
- Views: 72738
Re: OD18 - NH
The plan doesn't call for glass on the frames or stringers. I used 12 oz bias tape on all of them, one layer each side, per Cracker Larry's advice. Yesterday the bay got real sloppy after lunch, and I was glad I did. Nice to know it's there when you need to pound through a hard chop. Craig, I thoug...
- Wed Feb 14, 2018 8:29 am
- Forum: Builder's Power Boats
- Topic: Bruce Crandall Flyer Hydroplane
- Replies: 901
- Views: 100511
Re: Bruce Crandall Flyer Hydroplane
Yes they will be cut out together with the decking planks, reason I glassed and faired them is because I want to try and save the cut out to make it in to a lid for storage, so cockpit will be protected from the elements and vermin during storage and trailering. Now that is really thinking ahead, W...
- Wed Jan 10, 2018 7:55 am
- Forum: Builder's Power Boats
- Topic: Cape Man's Dory
- Replies: 2994
- Views: 367664
Re: Cape Man's Dory
Nice Write UP Craig Always enjoy reading about your cape sable trips.
Sorry to hear about the crud, but glad to hear Clara is like a new boat.
Ya'll take care,
Larry B
Sorry to hear about the crud, but glad to hear Clara is like a new boat.
Ya'll take care,
Larry B
- Sun Jan 07, 2018 2:47 pm
- Forum: Builder's Power Boats
- Topic: OD18 - NH
- Replies: 506
- Views: 72738
Re: OD18 - NH
Very Nice Work
Looks PERFECT from here,
much nicer than mine and no one has ever complained
Looks PERFECT from here,
much nicer than mine and no one has ever complained
- Thu Jan 04, 2018 8:31 am
- Forum: Power Boats
- Topic: OD18 - NH Technical Questions
- Replies: 25
- Views: 2400
Re: OD18 - NH Technical Questions
I'd just go with Hydraulic steering. I went with hydraulic and I came out of the locker. In my opinion I love the Hydraulic and would do it again in a minute.