Ordered a gallon of base and used probably half.Dan_Smullen wrote: ↑Sat May 09, 2020 5:01 pm What kind of coverage did you get? Quart or two for the outside?
SBW FRS-15 Build “Kestrel”
-
ChaisnTails
- Frequent Poster
- Posts: 27
- Joined: Fri Aug 23, 2019 8:50 am
- Location: Vero Beach FL
Re: SBW FRS-15 Build “Kestrel”
-
ChaisnTails
- Frequent Poster
- Posts: 27
- Joined: Fri Aug 23, 2019 8:50 am
- Location: Vero Beach FL
Re: SBW FRS-15 Build “Kestrel”
Haven’t updated in a while but a lot going on!
Console with grab bar designed
Received my new trailer!
Topside is leveled out where the decks meet the rub rail /flairs
Knee boards installed...glad I recently got these long clamps!
Decided to cut the rear bulkhead in half to make it a split bench! After much deliberation and discussion with fellow tiller operators this will be optimal. Made the bench removable though, so have the option for seating if needed. Also raised the rear deck so there’s a small “bilge well” in the rear to collect water to be pumped out
Transom eyes installed, deck glassed, and scored a couple great marketplace finds...cheap brand new WetSounds speakers and a used 20ft G Loomis push pole
3 rounds of blended filler/fairing
And this is how she sits today! Console and platform installed! Ready for primer.
Console with grab bar designed
And this is how she sits today! Console and platform installed! Ready for primer.
- Attachments
-
Re: SBW FRS-15 Build “Kestrel”
Nice progress!!!! Jeff
-
BB Sig
- Very Active Poster
- Posts: 1751
- Joined: Thu Sep 29, 2011 9:20 am
- Location: Tallahassee, FL
- Contact:
Re: SBW FRS-15 Build “Kestrel”
Beautiful build!
On the last picture, are you going to round over that edge? Sharp edges on most things tend to ding easier. Having not finished a boat, I can only imagine it is similar.
On the last picture, are you going to round over that edge? Sharp edges on most things tend to ding easier. Having not finished a boat, I can only imagine it is similar.
-
Dan_Smullen
- * Bateau Builder *
- Posts: 912
- Joined: Tue Aug 13, 2019 3:02 pm
- Location: VA
Re: SBW FRS-15 Build “Kestrel”
Beautiful lamination detail!
-
ChaisnTails
- Frequent Poster
- Posts: 27
- Joined: Fri Aug 23, 2019 8:50 am
- Location: Vero Beach FL
Re: SBW FRS-15 Build “Kestrel”
Yes! That’s actually an older photo, I’ve since routered the top and bottom of the rub rail (cypress wood) with I think a 3/8” bit? Can’t remember, but it’s nice round and smooth. Will do a multitude of layers of epoxy then varnish, then a stainless rib down the middle as well. But I got what you’re saying...I was concerned about the sharp edge cutting my fishing line!
Re: SBW FRS-15 Build “Kestrel”
Terrific looking build!
Dougster
Dougster
-
ChaisnTails
- Frequent Poster
- Posts: 27
- Joined: Fri Aug 23, 2019 8:50 am
- Location: Vero Beach FL
Re: SBW FRS-15 Build “Kestrel”
Been busy but not busy keeping y’all updated. Everything is painted, and almost time to mount the motor! Quick question...is everyone using 4200 to glue motor on, or just in and around the bolt holes (which are over drilled, filled, and redrilled)?
Used Alexseal paint, and Soft Sand for non skid, filling the method done by Boatworks Today on YouTube. Really came out fantastic!
Used Alexseal paint, and Soft Sand for non skid, filling the method done by Boatworks Today on YouTube. Really came out fantastic!
-
gstanfield
- * Bateau Builder *
- Posts: 4655
- Joined: Sun Jan 10, 2010 5:09 pm
Re: SBW FRS-15 Build “Kestrel”
Beautiful work!
Previous builds: FL14, NC16, and others...
Current build: FL14 (+10%)
Current build: FL14 (+10%)
Re: SBW FRS-15 Build “Kestrel”
Completely agree, beautiful work!!! Jeff
Who is online
Users browsing this forum: Yandex [Bot] and 7 guests