LB26 Strikers height

Power Boats only. Please include the boat type in your question.
fallguy1000
* Bateau Builder - Expert *
* Bateau Builder - Expert *
Posts: 10198
Joined: Tue Jan 12, 2010 12:25 am

Re: LB26 Strikers height

Post by fallguy1000 »

It is a bit confusing for sure.

Here are the pictures.

The knife points to waterline. The sole seems to be the line above that.
54DEA0C9-2BBC-4D6A-B38C-B89328D2867E.jpeg
Here the sole seems much higher than dwl.
CBB66CFC-3B66-4C62-B5E6-76B0B5B4E619.jpeg
Here, again at Frame E, the sole where people will walk is well above dwl. My apologies on all of these I have been misinterpreting perhaps and throwing off the designer maybe.
93B1A705-37F9-415B-803C-ED3BA338017A.jpeg
My boat build is here -------->

viewtopic.php?f=12&t=62495

Fatih
Frequent Poster
Frequent Poster
Posts: 135
Joined: Sat Dec 05, 2020 2:01 pm
Location: Ankara

Re: LB26 Strikers height

Post by Fatih »

fallguy1000 wrote: Wed Jun 09, 2021 11:03 am It is a bit confusing for sure.

Here are the pictures.

The knife points to waterline. The sole seems to be the line above that.
54DEA0C9-2BBC-4D6A-B38C-B89328D2867E.jpeg

Here the sole seems much higher than dwl.
CBB66CFC-3B66-4C62-B5E6-76B0B5B4E619.jpeg

Here, again at Frame E, the sole where people will walk is well above dwl. My apologies on all of these I have been misinterpreting perhaps and throwing off the designer maybe.
93B1A705-37F9-415B-803C-ED3BA338017A.jpeg
Dear Dan,
Yes .i am confusing because sole level seen higher than dwl at bulkheads G.
I have to wait JM's info.
Thx for your suppports.
Regards

Fatih
Frequent Poster
Frequent Poster
Posts: 135
Joined: Sat Dec 05, 2020 2:01 pm
Location: Ankara

Re: LB26 Strikers height

Post by Fatih »

jacquesmm wrote: Wed Jun 09, 2021 10:38 am
Fatih wrote: Wed Jun 09, 2021 10:09 am
But i have a nother question.
The sole will sit on the bulkheads right?Then,
What is the height of the sole as attached?
Any reference height from DWL or ?
Regards
The top of the sole is at the DWL.
Use that DWL as your reference and measure from there.
If you still have your molds, drop a couple of them in the hull and mark the DWL.
If not, redraw a couple of them and measure along the side. You can measure from the chine, redraw only that part.
You will end up with a line like the one shown by Fallguy.

That DWL is your reference. It will give you a level sole.
level
A small difference in the level of the sole does not matter but it must be level.
Dear Mr.Martens,
Thx for your response.But it seems that the level of sole is higher than the dwl on bulkheads frame G and E.
Can you pls recheck?
Regards

jacquesmm
Site Admin
Site Admin
Posts: 28215
Joined: Wed Aug 14, 2002 1:00 am
Location: Florida USA
Contact:

Re: LB26 Strikers height

Post by jacquesmm »

You are correct, I am wrong. The cockpit sole is well above the DWL. Let's refer only to the DWL.
The top of the outside stringer is 12 mm below that DWL.
The cockpit sole is at a slight angle: lower face is 154 mm above DWL at the transom and 228 mm at the cockpit bulkhead.
Jacques Mertens - Designer
http://boatbuildercentral.com

fallguy1000
* Bateau Builder - Expert *
* Bateau Builder - Expert *
Posts: 10198
Joined: Tue Jan 12, 2010 12:25 am

Re: LB26 Strikers height

Post by fallguy1000 »

jacquesmm wrote: Wed Jun 09, 2021 3:59 pm You are correct, I am wrong. The cockpit sole is well above the DWL. Let's refer only to the DWL.
The top of the outside stringer is 12 mm below that DWL.
The cockpit sole is at a slight angle: lower face is 154 mm above DWL at the transom and 228 mm at the cockpit bulkhead.
This would mean each frame varies in height, but there are no numbers in the drawings.

Is there any way to provide rough dimensions?
My boat build is here -------->

viewtopic.php?f=12&t=62495

fallguy1000
* Bateau Builder - Expert *
* Bateau Builder - Expert *
Posts: 10198
Joined: Tue Jan 12, 2010 12:25 am

Re: LB26 Strikers height

Post by fallguy1000 »

I suppose you could string to the frame locations if you did not have them.
My boat build is here -------->

viewtopic.php?f=12&t=62495

jacquesmm
Site Admin
Site Admin
Posts: 28215
Joined: Wed Aug 14, 2002 1:00 am
Location: Florida USA
Contact:

Re: LB26 Strikers height

Post by jacquesmm »

That sole does not sit on the stringers.
Jacques Mertens - Designer
http://boatbuildercentral.com

fallguy1000
* Bateau Builder - Expert *
* Bateau Builder - Expert *
Posts: 10198
Joined: Tue Jan 12, 2010 12:25 am

Re: LB26 Strikers height

Post by fallguy1000 »

jacquesmm wrote: Thu Jun 10, 2021 9:10 am That sole does not sit on the stringers.
Is the pitch on the frames done to move water aft for self bailing?

You said the sole is not level, so just curious about the 3" pitch change.
My boat build is here -------->

viewtopic.php?f=12&t=62495

jacquesmm
Site Admin
Site Admin
Posts: 28215
Joined: Wed Aug 14, 2002 1:00 am
Location: Florida USA
Contact:

Re: LB26 Strikers height

Post by jacquesmm »

fallguy1000 wrote: Thu Jun 10, 2021 11:07 am

Is the pitch on the frames done to move water aft for self bailing?
Yes. I design that in "big" boats.
Jacques Mertens - Designer
http://boatbuildercentral.com

jacquesmm
Site Admin
Site Admin
Posts: 28215
Joined: Wed Aug 14, 2002 1:00 am
Location: Florida USA
Contact:

Re: LB26 Strikers height

Post by jacquesmm »

Fatih, I am going to help by drawing a vertical section through the stringers center and will email it to you.
From there, you will have the shape of the bottom of the stringers relative to the DWL.
You will have to offset for the hull thickness but that is easy.
Jacques Mertens - Designer
http://boatbuildercentral.com

Post Reply

Who is online

Users browsing this forum: Bing [Bot] and 5 guests