**** This thread is picture heavy! ****
The purpose of this boat and the name come from my other ongoing build, a GT23 named Midstream. My plan is to have a folding front bow of the GT that I can load/unload kayaks from. I figured I would document this build separate from MidStream.
FS13 'Lil Stream
- BB Sig
- Very Active Poster
- Posts: 1750
- Joined: Thu Sep 29, 2011 9:20 am
- Location: Tallahassee, FL
- Contact:
FS13 'Lil Stream
Last edited by BB Sig on Thu Aug 17, 2017 9:10 pm, edited 1 time in total.
Re: FS13 'Lil Stream
BB, good seeing you this week. Have a nice holiday weekend!! Jeff
- BB Sig
- Very Active Poster
- Posts: 1750
- Joined: Thu Sep 29, 2011 9:20 am
- Location: Tallahassee, FL
- Contact:
Re: FS13 'Lil Stream
It was nice meeting the crew at Bateau. Too bad Jacques was not there but I bet he's having a lot more fun than any of us right now.
Here's tonight's work. Not bad for an hour after bible study... The wife came out and helped me trace while I was making the next cut.
I will try to get another hour or so in tomorrow night after church. I'll see if I can get the wife out there again. I'm amazed I got her out there tonight!
Here's tonight's work. Not bad for an hour after bible study... The wife came out and helped me trace while I was making the next cut.
I will try to get another hour or so in tomorrow night after church. I'll see if I can get the wife out there again. I'm amazed I got her out there tonight!
Re: FS13 'Lil Stream
BB, that is a huge amount accomplished in 1 hour!!! Nice, Jeff
- BB Sig
- Very Active Poster
- Posts: 1750
- Joined: Thu Sep 29, 2011 9:20 am
- Location: Tallahassee, FL
- Contact:
Re: FS13 'Lil Stream
I had to make a trip to Montana so I didn't get a lot done working on the boats for the last week. Here's a couple of pictures to show a short portion of my trip.
Sacajawea II is a 50' wooden boat that the tour was given on. The tour guide was a Cajun from Louisiana that gave a great history lesson on the area.
I finally had time to get some work done. I have about 90% cut out. I am waiting on a few pieces until I get the hull finished and take measurements off of the hull itself. I built an assembly table out of 2"x8"x12' joists that I will reuse after the boat for my kids fort. I used 3/4" plywood for the table top and some 4x4 oak legs that I had laying around. I didn't have to cut them to get a near perfect height. I got things laid out for gluing tomorrow evening.
Instead of making 4 transom cutouts and then gluing them together, I did two out of 4mm and used 9mm for the other two. It should save me on the gluing time. I am tempted to just glue a 4mm and a 9mm and call it good since I will only be using electric motors with this one.
Here are the transom knees that I did the same as the transom only this time I only cut them out of 9mm instead of two 4mm pieces.
Here's my under table storage. Not full yet but it shouldn't take long to fill it up.
Sacajawea II is a 50' wooden boat that the tour was given on. The tour guide was a Cajun from Louisiana that gave a great history lesson on the area.
I finally had time to get some work done. I have about 90% cut out. I am waiting on a few pieces until I get the hull finished and take measurements off of the hull itself. I built an assembly table out of 2"x8"x12' joists that I will reuse after the boat for my kids fort. I used 3/4" plywood for the table top and some 4x4 oak legs that I had laying around. I didn't have to cut them to get a near perfect height. I got things laid out for gluing tomorrow evening.
Instead of making 4 transom cutouts and then gluing them together, I did two out of 4mm and used 9mm for the other two. It should save me on the gluing time. I am tempted to just glue a 4mm and a 9mm and call it good since I will only be using electric motors with this one.
Here are the transom knees that I did the same as the transom only this time I only cut them out of 9mm instead of two 4mm pieces.
Here's my under table storage. Not full yet but it shouldn't take long to fill it up.
Re: FS13 'Lil Stream
Looking good Barry! Trip looked like it would be fun.
Re: FS13 'Lil Stream
Barry, looks like a great trip to Montana, beautiful State!! Nice work on the cutting!! Jeff
- BB Sig
- Very Active Poster
- Posts: 1750
- Joined: Thu Sep 29, 2011 9:20 am
- Location: Tallahassee, FL
- Contact:
Re: FS13 'Lil Stream
First two splices are made with assistance. The bigger one placed the fiberglass and moved some epoxy around. We'll see how it comes out!
Re: FS13 'Lil Stream
BB, great family project and glad to see them both involved!!! Jeff
-
- Frequent Poster
- Posts: 28
- Joined: Sat Aug 06, 2016 7:50 pm
- Location: NorCal
- Location: NorCal, Sonoma County
Re: FS13 'Lil Stream
Nice work so far. I'm interested in the FS13 so I'll be watching this thread to learn some building tricks.
Karlo,
Karlo,
Who is online
Users browsing this forum: Bing [Bot] and 5 guests