plywood Skoota interior finish for wood parts

Questions and Answers about the Woods Designs, multihulls and others.
jonnymac
Active Poster
Active Poster
Posts: 338
Joined: Sun Jun 21, 2020 8:33 am
Location: Eliot, ME

plywood Skoota interior finish for wood parts

Post by jonnymac »

I was looking at the skoota plans, the 24 to the 36. the plywood versions. What is done on the inside parts of the plywood on frame Skoota’s?

fallguy1000
* Bateau Builder - Expert *
* Bateau Builder - Expert *
Posts: 10198
Joined: Tue Jan 12, 2010 12:25 am

Re: plywood Skoota interior finish for wood parts

Post by fallguy1000 »

jonnymac wrote: Mon Jun 22, 2020 5:10 pm I was looking at the skoota plans, the 24 to the 36. the plywood versions. What is done on the inside parts of the plywood on frame Skoota’s?
The 24 is fully enclosed hulls; no access. You would seal with epoxy or do nothing.

The 36 has walk in hulls. Those you would seal with epoxy or epoxy primer.
My boat build is here -------->

viewtopic.php?f=12&t=62495

jonnymac
Active Poster
Active Poster
Posts: 338
Joined: Sun Jun 21, 2020 8:33 am
Location: Eliot, ME

Re: plywood Skoota interior finish for wood parts

Post by jonnymac »

Thanks for information. I can’t imagine leaving it uncoated, but I wasn’t sure what people did.

fallguy1000
* Bateau Builder - Expert *
* Bateau Builder - Expert *
Posts: 10198
Joined: Tue Jan 12, 2010 12:25 am

Re: plywood Skoota interior finish for wood parts

Post by fallguy1000 »

jonnymac wrote: Mon Jun 22, 2020 7:50 pm Thanks for information. I can’t imagine leaving it uncoated, but I wasn’t sure what people did.
You have to preseal stuff before assembly on the 24.

The 24 is really my favorite boat in the world. I would modify it a bit n ditch the aft cabin for benches.

I wish I owned one, I'd take it up to lakes in Canada.
My boat build is here -------->

viewtopic.php?f=12&t=62495

jonnymac
Active Poster
Active Poster
Posts: 338
Joined: Sun Jun 21, 2020 8:33 am
Location: Eliot, ME

Re: plywood Skoota interior finish for wood parts

Post by jonnymac »

It does seem very nice. I have two kids, so I need to sleep 4 which is what attracted me to this line of boats. I live in upstate NY near the mohawk river/erie canal. so lots of cruising that could be had in that boat. Work has me tied up for the next 14 months, hope to have a plan in place to start building then.

fallguy1000
* Bateau Builder - Expert *
* Bateau Builder - Expert *
Posts: 10198
Joined: Tue Jan 12, 2010 12:25 am

Re: plywood Skoota interior finish for wood parts

Post by fallguy1000 »

jonnymac wrote: Mon Jun 22, 2020 9:19 pm It does seem very nice. I have two kids, so I need to sleep 4 which is what attracted me to this line of boats. I live in upstate NY near the mohawk river/erie canal. so lots of cruising that could be had in that boat. Work has me tied up for the next 14 months, hope to have a plan in place to start building then.
The 24 is special. I hope you get to build it. I think Richard talked about dual engines for it as well. A couple 30hp motors would be cool, but probably short for autopilot.
My boat build is here -------->

viewtopic.php?f=12&t=62495

Post Reply

Who is online

Users browsing this forum: No registered users and 3 guests